{"id":579,"date":"2016-05-11T08:54:23","date_gmt":"2016-05-11T08:54:23","guid":{"rendered":"http:\/\/sim-cdm.it\/?page_id=579"},"modified":"2020-07-30T12:32:49","modified_gmt":"2020-07-30T10:32:49","slug":"resistori-carburo-di-silicio","status":"publish","type":"page","link":"https:\/\/sim-cdm.it\/en\/silicon-carbide-heating\/","title":{"rendered":"Silicon Carbide Heating"},"content":{"rendered":"<p>[vc_row][vc_column][vc_column_text]<\/p>\n<hr \/>\n<p><strong>SILICON CARBIDE HEATING<br \/>\n<\/strong><\/p>\n<p><strong>SIC RESISTORS FOR INDUSTRIAL ELECTRIC FURNACES<br \/>\n<\/strong><\/p>\n<p><strong>GENERAL DESCRIPTION<\/strong><\/p>\n<p>SIM S.r.l. SiC heating elements are silicon carbide<br \/>\nheating elements. SiC are rod shaped or tubular<br \/>\ndepending on the diameter. They have a central<br \/>\nheating section referred to as a hot zone and two<br \/>\nterminal sections called cold ends. There are two<br \/>\ntypes of SIM S.r.l. SiC:<br \/>\n1) The cold ends are impregnated with silicon<br \/>\nmetal &#8212; referred to as one piece, and<br \/>\n2) low resistance cold ends which are furnace<br \/>\nwelded to the hot zone &#8212; referred to as a three<br \/>\npiece or LRE (Low Resistance End) type.<br \/>\nThis lower electrical resistance cold end causes<br \/>\nthem to operate at a lower temperature. The extremities<br \/>\nof the elements are metallized with aluminum<br \/>\nto provide a low resistance contact surface to<br \/>\nwhich the electrical connections are made using<br \/>\nbraided aluminum straps.<br \/>\nSIM S.r.l. SiC resistors are described by giving the<br \/>\noverall length, the heating section length, and the<br \/>\ndiameter. As an example, RI 43 x 24 x 1 is a SIM<br \/>\nS.r.l. 43\u201d overall with a 24\u201d hot zone, and 1\u201d in<br \/>\ndiameter.<\/p>\n<p>&nbsp;<\/p>\n<p><strong>SUPERIOR PERFORMANCE<\/strong><\/p>\n<p>SIM S.r.l. SiC resistors will give you superior performance<br \/>\ndue to their high density &#8212; approximately<br \/>\n2.4 gms\/cc. This gives the SIM S.r.l. SiC<br \/>\nresistors very slow aging characteristics and additional<br \/>\nstrength.<\/p>\n<p>&nbsp;<\/p>\n<p><strong>INTERCHANGEABILITY<\/strong><\/p>\n<p>SIM S.r.l. SiC resistors are interchangeable with all<br \/>\nsilicon carbide heating elements manufactured in<br \/>\nEurope as well as higher resistance heating elements<br \/>\nmanufactured for the Asian and United States<br \/>\nmarkets. It is important to provide the nominal<br \/>\nelectrical resistance when ordering to SIM S.r.l.<br \/>\nPlease contact us, before attempting to substitute.<\/p>\n<p>&nbsp;<\/p>\n<p><strong>SIZES AVAILABLE<\/strong><\/p>\n<p>SIM S.r.l. SiC resistors can be manufactured in any<br \/>\nlength up to 228 inches (5800mm). The maximum<br \/>\nhot zone length is 166 inches (4216mm).<\/p>\n<p>&nbsp;<\/p>\n<p><strong>OPERATING TEMPERATURES<\/strong><\/p>\n<p>In an air or inert atmosphere of argon or helium<br \/>\nthe one SiC piece can be operated at furnace control<br \/>\ntemperatures up to 3100\u00b0F (1700\u00b0C), the three<br \/>\npiece SIM S.r.l. up to 2600\u00b0F (1425\u00b0C). There is a<br \/>\nprotective coating of silicon dioxide on the silicon<br \/>\ncarbide. Hydrogen reduces this coating and causes<br \/>\nthe SiC resistor to deteriorate. Very dry or very<br \/>\nwet hydrogen is detrimental to long service life.<br \/>\nNitrogen atmosphere applications are limited to<br \/>\n2500\u00b0F (1370\u00b0C) and 20 to 30 watts per square<br \/>\ninch (3.1 to 4.6 watts per square centimeter) maximum<br \/>\nsurface watt loading. Too high of a surface<br \/>\ntemperature will result in a silicon nitride reaction.<br \/>\nA thermally insulative layer forms around the<br \/>\nSiC resistor resulting in very high surface temperatures<br \/>\nwhich damage the resistor.<\/p>\n<p>&nbsp;<\/p>\n<p><strong>ELECTRICAL FEATURES<\/strong><\/p>\n<p>The silicon carbide resistor of SIM S.r.l. is a linear<br \/>\ntype resistance heater that converts electrical<br \/>\nenergy to heat energy &#8212; Joule\u2019s Law W = I\u00b2 x R,<br \/>\n(W = power in watts, I = current in amperes, R =<br \/>\nresistance in ohms).<br \/>\nThe SiC resistor hot zone is a self bonded silicon<br \/>\ncarbide. The lattice structure or bonds that hold<br \/>\nthe silicon carbide grain together are formed by<br \/>\nrecrystallizing the silicon carbide at very high<br \/>\ntemperatures. SIM S.r.l. are manufactured of green<br \/>\nsilicon carbide that is classed as an excess electron<br \/>\ntype semiconductor.<br \/>\nThe electrical resistance of a SiC resistor is difficult<br \/>\nto measure at room temperature due to minor impurities,<br \/>\nself heating, and contact resistance. Also<br \/>\nthe green silicon carbide has a negative resistance<br \/>\ntemperature characteristic from room temperature to approximately 1200\u00b0F (650\u00baC). It turns positive<br \/>\nat this point and remains so throughout its normal<br \/>\noperating temperature range.<br \/>\nThe nominal SiC resistor resistance is measured<br \/>\nat the calibrating temperature of 1960\u00baF (1071\u00b0C).<br \/>\nThe nominal resistance values of SiC resistors in<br \/>\nohms per unit of length are shown in Table A.<\/p>\n<p>&nbsp;<\/p>\n<p><strong>ELECTRICAL LOADING<\/strong><\/p>\n<p>SiC resistors are not sized to a specific wattage<br \/>\noutput like metallic heating elements. The amount<br \/>\nof energy that a SiC resistor is capable of converting<br \/>\nfrom electrical to heat energy depends on the<br \/>\nambient furnace temperature and atmosphere in<br \/>\nwhich the SiC resistor is operating.<br \/>\nWhen calculating the wattage capabilities of a<br \/>\nSiC resistor, the unit of watts output per unit of<br \/>\nradiating surface area is used. Figure 1 shows the<br \/>\nrecommended watt loading for a square inch or<br \/>\nsquare centimeter of radiating surface as a function<br \/>\nof furnace temperature.<br \/>\nTo determine the recommended wattage capabilities<br \/>\nof the SiC resistor start with Figure 1, knowing<br \/>\nthe furnace temperature and atmosphere in which<br \/>\nthe SiC resistor will be operated. Follow the temperature<br \/>\nline until you intersect the heavy black<br \/>\nline (choosing the appropriate line according to<br \/>\nthe atmosphere in which the SiC resistor will be<br \/>\noperating). Read the loading in watts per square<br \/>\nunit of radiating surface that can be applied to the<br \/>\nSiC resistor. To find the total amount of power one<br \/>\nSiC resistor could supply under these conditions,<br \/>\nmultiply this value by the radiating surface of the<br \/>\nSiC resistor. The radiating surface area is calculated<br \/>\nby multiplying the diameter times the hot zone<br \/>\nlength times pi (3.14).<\/p>\n<p>Example:<br \/>\nAt 2750\u00b0F the SiC resistor could be loaded to 35<br \/>\nwatts per square inch. Therefore, a resistor with<br \/>\n10 square inches of radiating surface could supply<br \/>\n350 watts, whereas a resistor with 200 square inches<br \/>\nof radiating surface could supply 7000 watts.<br \/>\n(At 1500\u00b0C the SiC could be loaded to 6 watts<br \/>\nper square centimeter. Therefore, a SiC with 100<br \/>\nsquare centimeters of radiating surface could supply<br \/>\n600 watts, whereas a SiC with 2000 square<br \/>\ncentimeters of radiating surface could supply<br \/>\n12,000 watts).<\/p>\n<p>&nbsp;<\/p>\n<p><strong>EXAMPLE OF RADIATING AREA:<\/strong><\/p>\n<p>The RI 43 x 24 x 1 has a hot zone length of 24 inches<br \/>\non a diameter of 1 inch. The radiating surface<br \/>\narea is 24 x 1 x 3.14, or 75.4 square inches.<br \/>\n(The RI 1092 x 610 x 25 has a hot zone length of<br \/>\n610mm and a diameter of 25mm. The radiating<br \/>\nsurface area is 610 x 25 x 3.14 or 47,885 square<br \/>\nmm, converted to centimeters is 478 square centimeters).<\/p>\n<p>&nbsp;<\/p>\n<p><strong>POWER SUPPLY<\/strong><\/p>\n<p>In the previous paragraph we explained how to<br \/>\ncalculate the recommended wattage output of the<br \/>\nSiC resistors.<br \/>\nNow we shall explain how to compute the electrical<br \/>\nrequirements to provide the recommended<br \/>\npower.<br \/>\nKnowing the wattage output and the resistance of<br \/>\nthe SiC resistors, you have two parts of an equation<br \/>\nwith three unknowns.<br \/>\nThis equation is E = \u221a (W x R), (E = nominal full<br \/>\nload voltage, W = rating of the SiC in watts, R = resistance<br \/>\nof the SIM SiC in ohms). The resistance of<br \/>\nthe SiC. can be calculated using the values found<br \/>\nin Table A.<br \/>\nWhen solving for E, you would obtain the voltage<br \/>\nrequired on a nominal SiC resistor to provide the<br \/>\nwattage output desired.<br \/>\nExample: A SiC resistor RI 43 x 24 x 1 has a resistance<br \/>\nof 1.21 ohms and 75 square inches of<br \/>\nradiating surface. Loading to 40 watts per square<br \/>\ninch, this SiC could provide 3000 watts. To find<br \/>\nthe nominal voltage solve for E.<\/p>\n<p>E = \u221a (W x R)<br \/>\nE = \u221a (3000 x 1.21)<br \/>\nE = 60 volts<\/p>\n<p>SiC resistors may be connected in parallel, series,<br \/>\nor combination thereof. Parallel connections are<br \/>\npreferred.<br \/>\nIn a parallel arrangement the voltage across all the<br \/>\nSiC is the same. In the formula W = E\u00b2 \u00f7 R, (W =<br \/>\nwatts, E = voltage, R = resistance) it can be seen<br \/>\nthat the greater the resistance, the lower the wattage<br \/>\noutput. The SiC resistors in the parallel circuit<br \/>\nwith the lowest resistance will supply more heat<br \/>\nenergy and therefore operate at a higher temperature.<br \/>\nThis higher SiC temperature will cause it to<br \/>\ngradually increase in resistance until all the SIM<br \/>\nS.r.l. have the same resistance. At this time the SiC<br \/>\nresistors should all have approximately the same<br \/>\nresistance values and surface temperatures and<br \/>\ntherefore remain in balance.<br \/>\nTo compute the network resistance of a group of<br \/>\nSiC resistors the following formula may be used:<br \/>\nRn = R x S \u00f7 P (Rn = network resistance, R = resistance<br \/>\nof SiC, S = number of SiC connected in a<br \/>\nseries, P = number of parallel circuits).<br \/>\nExample: Eight SiC RI 43 x 24 x 1 (R = 1.21 ohms)<br \/>\nconnected 2 in series (S = 2) and 4 parallel groups (P = 4).<\/p>\n<p>Rn = R x S \u00f7 P<br \/>\nRn = 1.21 x 2 \u00f7 4<br \/>\nRn = 0.6 ohms<\/p>\n<p>To compute the nominal voltage required to power<br \/>\na set of SiC, we shall use a combination of the<br \/>\nformulas used in the two previous examples. En<br \/>\n= \u221a (Wt x Rn), (En = nominal network voltage, Rn<br \/>\n= network resistance, Wt = total wattage output).<br \/>\nExample: Eight SiC RI 43 x 24 x 1 (R= 1.21 ohms)<br \/>\nconnected 2 in series, 4 parallel groups. Each SiC<br \/>\nprovides 3000 watts. Wt = 8 x 3000 = 24,000<br \/>\nwatts. Rn = 0.60 ohms.<\/p>\n<p>En = \u221a (Wt x Rn)<br \/>\nEn = \u221a (24,000 x 0.6)<br \/>\nEn = 120 volts<\/p>\n<p>The resistance of SiC resistors increases gradually<br \/>\nduring their useful life. Therefore, some means of<br \/>\nkeeping the power input to the kiln or furnace at a<br \/>\nlevel sufficiently high to maintain the desired temperature<br \/>\nis required.<br \/>\nHistorically, expensive voltage varying equipment<br \/>\nsuch as multiple tap transformers or saturable reactors<br \/>\nwere recommended for all but the very low<br \/>\ntemperature applications.<br \/>\nSiC resistors can be used directly on the line (fixed<br \/>\nvoltages) at temperatures up to 2400\u00b0F (1315\u00b0C).<br \/>\nTo compensate for the reduced output as the SiC<br \/>\nresistors gradually age or increase in resistance,<br \/>\nthe furnace or kiln is initially overpowered by<br \/>\n25% to 50%. This type of arrangement eliminates<br \/>\nthe expensive voltage varying equipment and has<br \/>\nproven very satisfactory in many applications. It is<br \/>\nnot recommended when fine process temperature<br \/>\ncontrol is required.<\/p>\n<p>Assume a furnace will require approximately<br \/>\n24,000 watts after all heat losses and load factors<br \/>\nhave been considered. Increasing this 24,000<br \/>\nby 25% to 50% gives a wattage requirement of<br \/>\nbetween 30,000 and 36,000 watts.<br \/>\nBy taking another look at the previous examples<br \/>\nit can be seen that 10 SiC RI 43 x 24 x 1 connected<br \/>\ntwo in series, five parallel groups on 120<br \/>\nvolts would supply the 30,000 watts. If 12 SiC of<br \/>\nthe same size were used, the output would be<br \/>\n36,000 watts. Twelve SiC connected four in series<br \/>\nper phase on 240 volts would make a balanced<br \/>\nthree phase 240 volt network.<br \/>\nThe temperature of the kiln or furnace is controlled<br \/>\nby an off-on controller. When the SiC resistors<br \/>\nare new they will only be powered for 24\/30 or 24\/36 of an hour. As the SiC increase in resistance they will be on for a greater percentage of the time.<br \/>\nWhen they have increased in resistance to a point at which they supply 24,000 watts, they will be on<br \/>\n100% of the time. A SCR (silicon controlled rectifier) or thyrister can also be used.<br \/>\nFor applications where close temperature control is desired and\/or for temperatures above 2400\u00baF<br \/>\n(1315\u00baC) a device for increasing the voltage to the SIM S.r.l. is required. There are several methods of<br \/>\nproviding this variable voltage source:<\/p>\n<p><strong>1<\/strong> &#8211; The multiple tap transformer is the most common, because it is usually the least expensive. The<br \/>\nsecondary of the transformer is provided with taps which usually vary in number from 10 to 36. By carefully selecting the voltage taps, the correct voltage output to match the resistance of the SiC resistors<br \/>\nover their complete useful life can be made.<\/p>\n<p><strong>2<\/strong> &#8211; Saturable reactors and induction regulators are used to provide a stepless voltage control. They are<br \/>\nalso sometimes used with multiple tap transformers.<\/p>\n<p><strong>3<\/strong> &#8211; Capacitor controls are used infrequently. They, of course, will tend to improve a power factor, which<br \/>\nmakes their use desirable in some areas.<\/p>\n<p><strong>4<\/strong> &#8211; Silicon controlled rectifiers, (SCR) have become quite popular with the advances in solid state devices.<\/p>\n<p>To compensate for the reduced output as the SiC increase in resistance, a voltage range is required that<br \/>\nwill compensate for a 100% increase in the SIM S.r.l. resistance. The following formula may be used<br \/>\nto calculate Emax : Emax = \u221a(Wt x Rn) x 1.5, (Emax = recommended maximum voltage required to<br \/>\ncompensate for increase in resistance due to aging and resistance tolerance, Wt = rating of transformer<br \/>\nin watts, Rn = network resistance of the SiC, 1.5 = minimum margin to accommodate the doubling of<br \/>\nthe SiC resistance and the +20% resistance tolerance). A higher value will offer slightly longer usable<br \/>\nservice life.<br \/>\nExample: The transformer is rated at 24 KVA and has a computed nominal full load voltage of 120 volts.<\/p>\n<p>(Rn = 0.6, Wt = 24,000).<br \/>\nEmax = \u221a (Wt x Rn) x 1.5<br \/>\nEmax = \u221a (24,000 x 0.6) x 1.5<br \/>\nEmax = 180 volts<\/p>\n<p>[\/vc_column_text][vc_masonry_media_grid element_width=&#8221;12&#8243; grid_id=&#8221;vc_gid:1466600213708-fa5fb8e2b4a8a00534615a3fc128a44f-10&#8243; include=&#8221;1110&#8243;][\/vc_column][\/vc_row][vc_row][vc_column][vc_column_text]<\/p>\n<p>&nbsp;<\/p>\n<p>The nominal full load voltage and maximum voltage have been computed. When specifying the transformer<br \/>\nthe nominal full load voltage is usually reduced by 5% to 10% to allow for the minus 20%<br \/>\nresistance tolerance of the SiC resistor. Also, lower voltage taps are usually provided for idling and slow<br \/>\nheatups.<br \/>\nTo calculate the minimum voltage, take 70% of the nominal voltage. For periodic applications, take<br \/>\n30% of the nominal full load voltage.<br \/>\nAuto transformers may be used if primary voltage is 230 volts or less. They should not be used in a three<br \/>\nphase arrangement. Accepted practice limits the secondary voltage on all transformers to 300 volts.<br \/>\nAbove this refractory voltage leakage becomes a problem. When computing the size of the voltage<br \/>\nsteps between taps, a value of 5% of the nominal full load voltage is often used. When SCR or thyrister<br \/>\ncontrols are used on the primary, fewer taps are required. For example, if 6 taps are used, the idling tap<br \/>\ncan be 0.7 x nominal voltage, then each consecutive tap would be 14% higher. For 8 taps, the idling<br \/>\ntap would again be 0.7 x nominal voltage, each consecutive tap at 9.1% higher than the preceding.<\/p>\n<p>&nbsp;<\/p>\n<p><strong>EASE OF REPLACEMENT<br \/>\n<\/strong><\/p>\n<p>SiC resistors can be replaced while the furnace is at operating temperature. The power to the SiC<br \/>\nresistors being changed should be shut off, the spring clips and aluminum braid released, and the old<br \/>\nSiC removed. The new SiC should be inserted smoothly through the hot furnace with sufficient speed<br \/>\nto insure that the aluminum is not melted off the terminal end but not so fast as to cause thermal shock.<\/p>\n<p>&nbsp;<\/p>\n<p><strong>SERVICE LIFE<\/strong><\/p>\n<p>SiC resistors increase gradually in resistance with use. This characteristic of increasing in resistance is<br \/>\ncalled aging. Aging is a function of the following:<\/p>\n<p><strong>1<\/strong> &#8211; Operating temperature<\/p>\n<p><strong>2 <\/strong>&#8211; Electrical loading (usually expressed in watts per square inch or watts per square centimeter of<br \/>\nSiC radiating surface)<\/p>\n<p><strong>3 <\/strong>&#8211; Atmosphere<\/p>\n<p><strong>4 <\/strong>&#8211; Type of operation (continuous or intermittent)<\/p>\n<p><strong>5 <\/strong>&#8211; Operating and maintenance techniques<\/p>\n<p>&nbsp;<\/p>\n<p><strong>MOUNTING<\/strong><\/p>\n<p>There are no restrictions on the mounting positions of SiC resistors, although the horizontal and vertical<br \/>\npositions are the more common. Extreme caution should be used when mounting to ensure that the SiC<br \/>\nare not placed in tension. There should be adequate freedom to allow for the furnace and SiC resistors<br \/>\nexpand and contract independently.<br \/>\nWhen mounting SiC resistors vertically they must be supported on the lower end by electrically insulated supports.<br \/>\nSiC resistors should have their heating sections centered in the furnace chamber so that no portion of<br \/>\nthe heating section extends into the furnace wall. A conical or truncated cone shaped recess 1\/2 inch<br \/>\n(13mm) deep is sometimes located on each interior wall where the SiC passes through. This allows the<br \/>\nhot zone to radiate properly and helps maintain a uniform temperature in the kiln.<\/p>\n<p>&nbsp;<\/p>\n<p><strong>FURNACE HEATING CHAMBER<\/strong><\/p>\n<p>The furnace heated chamber dimension, which the SiC spans, can be the same as the hot zone length<br \/>\nof the SiC as shown by the SiC resistor under the load in Figure 3. Alternately the furnace heating chamber<br \/>\ndimension, which the SiC spans, can be one inch (25mm) less than the effective heating length of<br \/>\nthe SiC. In this case there must be a 45\u00b0 conical recess in the furnace wall as shown in Figure 3 for the<br \/>\nSiC resistor above the load. Recommended terminal hole diameters for various refractory walls and SiC<br \/>\nsizes are shown in Table B.<br \/>\nSIM S.r.l. should not be placed closer than two SIM S.r.l. diameters to each other or one and one half<br \/>\nSIM S.r.l. diameters to a wall or other reflecting body. If the SIM S.r.l. is not able to dissipate heat energy<br \/>\nequally in all directions, it may cause local overheating and possible failure.<\/p>\n<p>&nbsp;<\/p>\n<p>SPECIFICHE E CORRISPONDENZE[\/vc_column_text][vc_masonry_media_grid element_width=&#8221;12&#8243; grid_id=&#8221;vc_gid:1466600213961-c7d86eb8bdf766622ef3b1ce3e58a89e-6&#8243; include=&#8221;1111&#8243;][\/vc_column][\/vc_row][vc_row][vc_column][vc_column_text]<\/p>\n<p>&nbsp;<\/p>\n<p><strong>SPECIFICATIONS AND MATCHING<\/strong><\/p>\n<p>SiC resistors have a manufactured tolerance of plus or minus 20% on the nominal resistance. All SiC<br \/>\nresistors are calibrated at least twice prior to shipping to ensure their being within specifications. The<br \/>\ncalibrated amperage of each SiC resistor is marked on the carton and right hand end of each SiC. When<br \/>\ninstalling, arrange SiC resistors with amperage values as close to each other as available. Longer service<br \/>\nlife will be obtained when series connected SiC resistors are matched in resistance. SiC resistors are<br \/>\nshipped as closely matched as possible.<\/p>\n<p>&nbsp;<\/p>\n<p><strong>AVAILABILITY<\/strong><\/p>\n<p>SiC resistors can be shipped from stock, or two to three weeks after receipt of an order.<\/p>\n<p>&nbsp;<\/p>\n<p><strong>CUSTOM CONFIGURATIONS<\/strong><br \/>\nSpecial sizes and shapes are available. Cold ends can be different lengths. This, for example, would<br \/>\nbe applicable for furnaces with arched roofs that require longer cold ends through the roof and shorter<br \/>\nthrough the floor.<br \/>\nAnother modification is a two-temperature hot zone. This, for example, would be helpful to get additional heat energy into the lower, more densely loaded tunnel kiln. While this special modified hot<br \/>\nzone will not create a specific temperature differential, it does offer a convenient way to get more heat<br \/>\nenergy into a specific area of a furnace.<br \/>\nThe right angle (RA) shown here, has all the electrical characteristics of the RI. The cold ends are attached perpendicular to the hot zone. The RA is normally installed with the cold end through the roof of the furnace.<\/p>\n<p>&nbsp;<\/p>\n<p><strong>OUR COMPLETE RANGE OF HEATING ELEMENTS IN SILICON CARBIDE<br \/>\n<\/strong><\/p>\n<p><strong>Three Piece Straight Heating Elements SIC Rods<\/strong><\/p>\n<p>The Three Piece Straight heating elements SIC Rods have low resistance welded (LRE) cold ends.<br \/>\nThese ends are cooler any other one piece cold ends. The maximum featured temperature of the rods<br \/>\nis 1550\u00b0C and for better energy efficiency, heat is concentrated in the furnace, not on the ends of the<br \/>\nrods. With the highest Hot: Cold ratio of 1:40, these rods make one of the most efficient Silicon Carbide<br \/>\nHeaters.[\/vc_column_text][vc_masonry_media_grid element_width=&#8221;12&#8243; grid_id=&#8221;vc_gid:1466600214247-ccf4c61fedd7e48463f009685d7a650f-6&#8243; include=&#8221;625&#8243;][vc_masonry_media_grid element_width=&#8221;12&#8243; gap=&#8221;30&#8243; grid_id=&#8221;vc_gid:1466600214319-e563fdccf5b711eb632bd5b8f17805f6-7&#8243; include=&#8221;628&#8243;][\/vc_column][\/vc_row][vc_row][vc_column][vc_column_text]<\/p>\n<p><strong>Reaction Bonded Single Spiraled Heating Elements<\/strong><\/p>\n<p>The Reaction Bonded Silicon Carbide is used in the fabrication of SPIRAL Silicon Carbide heating Elements. These are available in different sizes ranging from 12mm to 50mm in diameters and 2250mm<br \/>\nin length. They are spiraled heating elements, shaped in a thin wall and finely grained form of reaction bonded silicon carbide. These can withstand high electrical loads, rapid heating &amp; cooling cycles and thermal shocks. To suit various heating processes, the elements are available in different forms.<\/p>\n<p>[\/vc_column_text][vc_masonry_media_grid element_width=&#8221;12&#8243; grid_id=&#8221;vc_gid:1466600214628-4964d2fd6eb9d823995b8f5573b628c3-8&#8243; include=&#8221;633&#8243;][vc_masonry_media_grid element_width=&#8221;12&#8243; grid_id=&#8221;vc_gid:1466600214713-1d6e0237c44458793cd3253c022b2b33-0&#8243; include=&#8221;634&#8243;][\/vc_column][\/vc_row][vc_row][vc_column][vc_column_text]<\/p>\n<p>&nbsp;<\/p>\n<p><strong>Reaction Bonded Double Spiraled Heating Elements<\/strong><\/p>\n<p>The Reaction Bonded Double Spiraled Heating Elements possess all the terminal<br \/>\nconnections at one end with the density of 3.3 Gms.\/cc ? 3.4 Gms.\/cc.<br \/>\nThese elements are ideal in the conditions, where the furnace access is limited<br \/>\nto any one plane.[\/vc_column_text][vc_masonry_media_grid element_width=&#8221;12&#8243; grid_id=&#8221;vc_gid:1466600215019-d6944dca4fbb64159e9f7d6bec70753e-10&#8243; include=&#8221;641&#8243;][vc_masonry_media_grid element_width=&#8221;12&#8243; grid_id=&#8221;vc_gid:1466600215109-5e4a220c4623267f646a53e6e21c5637-0&#8243; include=&#8221;642&#8243;][\/vc_column][\/vc_row][vc_row][vc_column][vc_column_text]<\/p>\n<p><strong>U-Shaped Heating Elements SIC Rods<\/strong><\/p>\n<p>The \u2018U\u2019 Shaped heating elements are<br \/>\nthe SIC rods that are joined from both<br \/>\nthe terminals in a form of thickened<br \/>\nbridge. These rods are ideal for the<br \/>\nconditions where one single rod is not<br \/>\nable to span the heating chamber.<br \/>\nFurther, these rods are also good<br \/>\nfor radiant tube systems and<br \/>\ndrop through designs. [\/vc_column_text][vc_masonry_media_grid element_width=&#8221;12&#8243; grid_id=&#8221;vc_gid:1466600215461-3911bdb85eab6d301f66a250cc944fd6-10&#8243; include=&#8221;646&#8243;][vc_masonry_media_grid element_width=&#8221;12&#8243; grid_id=&#8221;vc_gid:1466600215553-1e07cb34019798166eacd4e84c9ff41d-9&#8243; include=&#8221;648&#8243;][\/vc_column][\/vc_row][vc_row][vc_column][vc_column_text]<\/p>\n<p><strong>Drum (or dumbbell) shaped Silicon Carbide Heating Elements tamburo<\/strong><\/p>\n<p>The enlarged cold ends of the heating elements give them the name of Dumbbell Shaped Silicon<br \/>\nCarbide Heating Elements. The cold ends of the elements lower down the electrical resistance and<br \/>\nhelps in increasing the cold end cross<br \/>\nsection that is turn lowers the cold end<br \/>\noperating temperature.<br \/>\nIn the modern dumbbell alpha rods,<br \/>\nthe advanced technology is used for<br \/>\nkeeping the ends of the terminals cool,<br \/>\nthus the over sized cold ends are no longer<br \/>\nrequired. Old style resistance ratio was 1:3.<br \/>\nNew resistance ratio is 1:40 Maximum temperature is 1550 deg. C (For Dimensions, Resistance, etc. kindly contact us) [\/vc_column_text][vc_masonry_media_grid element_width=&#8221;6&#8243; grid_id=&#8221;vc_gid:1466600215929-78de663f52b10f3235a68f1e9f7945ae-10&#8243; include=&#8221;651&#8243;][\/vc_column][\/vc_row]<\/p>","protected":false},"excerpt":{"rendered":"<p>[vc_row][vc_column][vc_column_text] SILICON CARBIDE HEATING SIC RESISTORS FOR INDUSTRIAL ELECTRIC FURNACES GENERAL DESCRIPTION SIM S.r.l. SiC heating elements are silicon carbide heating elements. SiC are rod shaped or tubular depending on the diameter. They have a central heating section referred to as a hot zone and two terminal sections called cold ends. There are two types [&hellip;]<\/p>\n","protected":false},"author":1,"featured_media":1473,"parent":0,"menu_order":0,"comment_status":"closed","ping_status":"closed","template":"","meta":{"footnotes":""},"class_list":["post-579","page","type-page","status-publish","has-post-thumbnail","hentry"],"_links":{"self":[{"href":"https:\/\/sim-cdm.it\/en\/wp-json\/wp\/v2\/pages\/579","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/sim-cdm.it\/en\/wp-json\/wp\/v2\/pages"}],"about":[{"href":"https:\/\/sim-cdm.it\/en\/wp-json\/wp\/v2\/types\/page"}],"author":[{"embeddable":true,"href":"https:\/\/sim-cdm.it\/en\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/sim-cdm.it\/en\/wp-json\/wp\/v2\/comments?post=579"}],"version-history":[{"count":64,"href":"https:\/\/sim-cdm.it\/en\/wp-json\/wp\/v2\/pages\/579\/revisions"}],"predecessor-version":[{"id":1462,"href":"https:\/\/sim-cdm.it\/en\/wp-json\/wp\/v2\/pages\/579\/revisions\/1462"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/sim-cdm.it\/en\/wp-json\/wp\/v2\/media\/1473"}],"wp:attachment":[{"href":"https:\/\/sim-cdm.it\/en\/wp-json\/wp\/v2\/media?parent=579"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}